| Chung-huang Yu, Peter S. Walker, Michael E. Dewar |
------>authors3_c=None ------>paper_class1=1 ------>Impact_Factor=None ------>paper_class3=2 ------>paper_class2=1 ------>vol=34 ------>confirm_bywho=tzengcr ------>insert_bywho=chyu ------>Jurnal_Rank=None ------>authors4_c=None ------>comm_author= ------>patent_EDate=None ------>authors5_c=None ------>publish_day=None ------>paper_class2Letter=None ------>page2=1021 ------>medlineContent= ------>unit=E0112 ------>insert_date=20011024 ------>iam=1 ------>update_date= ------>author=??? ------>change_event=5 ------>ISSN=None ------>authors_c=None ------>score=500 ------>journal_name=Journal of Biomechanics ------>paper_name=The effect of design variables of condylar total knees on the joint forces in step climbing based on a computer model ------>confirm_date=20030509 ------>tch_id=088010 ------>pmid=11448693 ------>page1=1011 ------>fullAbstract=The ability to climb a steep step or rise from a low chair after total knee replacement may be enhanced if the required force in the quadriceps muscle is reduced. This can potentially be achieved if the total knee produces a large lever arm measured from the femoral-tibial contact point to the patellar ligament. A reduced quadriceps force would also reduce the patello-femoral force and the femoral-tibial contact force. The contact point location is likely to be a function of the geometry of the femoral and tibial components in the sagittal plane, including the relative distal and posterior radii of the femoral profile, the location of the bottom-of-the-dish of the tibial surface, the radius of the tibial surface, and the presence or absence of the posterior cruciate ligament. A three-dimensional model of the knee was developed including the quadriceps and various ligaments. In the study, the motion was confined to flexion extension and displacement in the sagittal plane. The quadriceps was assumed to be the only muscle acting. A standard software package (Pro/Mechanica) was used for the analysis. For a femoral component with a smaller distal radius, there was 12% reduction in the quadriceps muscle force and up to 11% reduction in the patello-femoral force from about 100 up to 60 degrees flexion. However, apart from that, there were less than 10% differences in all the forces as a function of all of the design variables studied. This was attributed to the relatively small changes in the lever arm of the patella tendon, since the tendon moves in an anterior-posterior direction along with the femur. An additional factor explaining the results was the change in the anterior-posterior contact point as controlled by the forces in the patella tendon and in the soft tissues. The results imply that for a standard condylar replacement knee, the muscle and contact forces are not greatly affected by the geometrical design variables. ------>tmu_sno=None ------>sno=4514 ------>authors2=None ------>authors3=None ------>authors4=None ------>authors5=None ------>authors6=None ------>authors6_c=None ------>authors=Chung-huang Yu, Peter S. Walker, Michael E. Dewar ------>delete_flag=0 ------>SCI_JNo=None ------>authors2_c=None ------>publish_area=None ------>updateTitle=The effect of design variables of condylar total knees on the joint forces in step climbing based on a computer model. ------>language=2 ------>check_flag= ------>submit_date= ------>country=None ------>no=8 ------>patent_SDate=None ------>update_bywho= ------>publish_year=2001 ------>submit_flag= ------>publish_month=None |